MultiPlus Inverter/Charger 12V/24V 3000VA
- Regular Price
- Sale Price
- Regular Price
- Unit Price
- translation missing: en.general.accessibility.unit_price_separator
WeeBoats eCommerce store is not currently accepting orders
The MultiPlus, as the name suggests, is a combined inverter and charger in one elegant package. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology, plus multiple system integration features.
The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions, the MultiPlus has several advanced features discussed below.
The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers
and other electronic equipment will continue to operate without disruption.
The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example can be connected to this output (second output available on models rated at 3 kVA
Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units, for example, will provide 15 kW / 18 kVA output power with 420 Amps charging capacity.
In addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not all: with three strings of six parallel units a 45 kW / 54 kVA three-phase inverter and 1,260A charger can be built.
Two units can be stacked to provide 120-0-120V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30 kW / 36 kVA of split phase power.
The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 20 A per 3 kVA Multiplus at 120 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.
This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
The main output provides a powerful charge to the battery system by means of advanced 'adaptive charge' software. The software fine-tunes the three stage automatic process to suit the condition of the battery and adds a fourth stage for long periods of float charging. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery.
After installation, the MultiPlus is ready to go. If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches; no computer needed.
Alternatively, VE.Net can be used instead of the DIP switches. Software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several advanced features.
Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).
Color Control GX or other GX devices. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
When connected to the internet, systems with a Color Control GX or other GX device can be accessed and settings can be changed remotely.
Wee Expert Tip - The SmartShunt battery monitor will enable you to monitor the state-of-charge for your batteries all through a Bluetooth connection to the VictronConnect app.
MultiPlus User Manual Covers Models 12 | 3000 | 120 - 50 | 120V (PMP122301102) and 24 | 3000 | 70 - 50 | 120V (PMP242301102) with firmware xxxx400 or higher
MultiPlus Service Manual Covers Models 12 | 3000 | 120 - 50 | 120V (PMP122301102) and 24 | 3000 | 70 - 50 | 120V (PMP242301102) with firmware xxxx400 or higher
Connecting Lithium Batteries to the MultiPlus
MultiPlus Inverter/Charger 12/24VDC 3kVA Datasheet
GENERAL SPECIFICATIONS (see datasheet for complete specifications)
|Transfer switch (A)||50A|
|Inverter input voltage range (V DC)||
9.5 - 17 V
19 - 33 V
|Inverter output voltage & frequency||
120 VAC +/- 2% at 60 Hz +/- 0.1%
|Inverter continuous output power at 77F (VA)||3000 VA|
|Inverter continuous output power at 77F (W)||2400 W|
|Inverter peak power (W)||6000 W|
|Charger AC Input||95 - 140 VAC at 45 - 65 Hz (Power Factor: 1)|
|Charge voltage "absorption" (VDC)||
|Charge voltage "float" (VDC)||
|Charge voltage "storage" (VDC)||
|Charge current, house battery (A)||
|Charge current, starter battery (A)||
|Charger battery temperature sensor||Yes|
|Auxiliary output||Yes (32 A)|
|Programmable relay||Yes (3x)|
|Protection||See datasheet for details|
|Operating temp, range||-40 to +65°C / -40 to +150°F (fan assisted cooling)|
|Humidity (non-condensing)||Up to 95%|
|VE.Bus communication port||
For parallel and three phase operation, remote monitoring, and system integration
|General purpose communication port||
A.o. to communicate with a lithium ion battery BMS
|Material & Color||Aluminium (blue RAL 5012)|
|Battery connection||M8 bolts (2 plus and 2 minus connections)|
|120V AC - connection||Screw-terminal 6 AWG (13mm2)|
|Dimensions (H x W x D)||
362 x 258 x 218 mm (14.3 x 10.2 x 8.6 in)
|Safety||UL 1741, UL 458, CSA C22.2, EN 60335-1, EN 60335-2-29|
|Emission / Immunity||EN-IEC 61000-3-2/3-3/, EN-IEC 61000-6-1/6-2/6-3|